RESUMEN El objetivo del estudio fue evaluar el efecto en la estabilidad de las nanopartículas de plata sintetizadas por ruta química, como función de la variación del tiempo de exposición de la intensidad luminosa. Se evaluaron por espectrofotometría UV-Vis dos casos, el primero para solución coloidal, el cual mostró tener su pico de absorbancia en 434 nm, típico en nanopartículas de plata con morfología esférica; en un segundo caso para solución coloidal bajo exposición de intensidad luminosa constante (4409 lux) con tiempos que van desde 15 horas hasta 48 horas. Los resultados sugieren el incremento del diámetro de las nanoesferas en función al incremento del tiempo de exposición luminosa, así como un aumento de la absorbancia, lo que indica una posible reacción incompleta y una mayor producción.

La investigación aborda la nanofertilización sostenible y sus impactos en el proceso de germinación de las semillas de quinua. El estudio se centra en el uso de nanopartículas de plata producidas mediante síntesis verde, destacando la importancia de los métodos ecológicos en la nanotecnología agrícola. A través de evaluaciones detalladas y análisis estadísticos, examinamos cómo estas nanopartículas afectan el crecimiento inicial de las semillas de quinua. Los resultados ofrecen información esencial sobre la eficacia de la nanofertilización ecológica para promover el desarrollo de la germinación de este cultivo clave. Este estudio surge como una valiosa contribución a la vanguardia de la nanotecnología agrícola, destacando su enfoque directo en la búsqueda activa de soluciones sostenibles para optimizar la productividad agrícola. Al profundizar en las ventajas intrÃ...

The excessive use of fossil sources for the generation of electrical energy and the increase in different organic wastes have caused great damage to the environment; these problems have promoted new ways of generating electricity in an eco-friendly manner using organic waste. In this sense, this research uses single-chamber microbial fuel cells with zinc and copper as electrodes and pineapple waste as fuel (substrate). Current and voltage peaks of 4.95667 ± 0.54775 mA and 0.99 ± 0.03 V were generated on days 16 and 20, respectively, with the substrate operating at an acid pH of 5.21 ± 0.18 and an electrical conductivity of 145.16 ± 9.86 mS/cm at two degrees Brix. Thus, it was also found that the internal resistance of the cells was 865.845 ± 4.726 Ω, and a maximum power density of 513.99 ± 6.54 mW/m2 was generated at a current density of 6.123 A/m2, and the final FTIR spectrum sho...

The excessive use of fossil sources for the generation of electrical energy and the increase in different organic wastes have caused great damage to the environment; these problems have promoted new ways of generating electricity in an eco-friendly manner using organic waste. In this sense, this research uses single-chamber microbial fuel cells with zinc and copper as electrodes and pineapple waste as fuel (substrate). Current and voltage peaks of 4.95667 ± 0.54775 mA and 0.99 ± 0.03 V were generated on days 16 and 20, respectively, with the substrate operating at an acid pH of 5.21 ± 0.18 and an electrical conductivity of 145.16 ± 9.86 mS/cm at two degrees Brix. Thus, it was also found that the internal resistance of the cells was 865.845 ± 4.726 Ω, and a maximum power density of 513.99 ± 6.54 mW/m2 was generated at a current density of 6.123 A/m2, and the final FTIR spectrum sho...

The excessive use of fossil sources for the generation of electrical energy and the increase in different organic wastes have caused great damage to the environment; these problems have promoted new ways of generating electricity in an eco-friendly manner using organic waste. In this sense, this research uses single-chamber microbial fuel cells with zinc and copper as electrodes and pineapple waste as fuel (substrate). Current and voltage peaks of 4.95667 ± 0.54775 mA and 0.99 ± 0.03 V were generated on days 16 and 20, respectively, with the substrate operating at an acid pH of 5.21 ± 0.18 and an electrical conductivity of 145.16 ± 9.86 mS/cm at two degrees Brix. Thus, it was also found that the internal resistance of the cells was 865.845 ± 4.726 Ω, and a maximum power density of 513.99 ± 6.54 mW/m2 was generated at a current density of 6.123 A/m2 , and the final FTIR spectrum s...

The excessive use of fossil sources for the generation of electrical energy and the increase in different organic wastes have caused great damage to the environment; these problems have promoted new ways of generating electricity in an eco-friendly manner using organic waste. In this sense, this research uses single-chamber microbial fuel cells with zinc and copper as electrodes and pineapple waste as fuel (substrate). Current and voltage peaks of 4.95667 ± 0.54775 mA and 0.99 ± 0.03 V were generated on days 16 and 20, respectively, with the substrate operating at an acid pH of 5.21 ± 0.18 and an electrical conductivity of 145.16 ± 9.86 mS/cm at two degrees Brix. Thus, it was also found that the internal resistance of the cells was 865.845 ± 4.726 Ω, and a maximum power density of 513.99 ± 6.54 mW/m2 was generated at a current density of 6.123 A/m2 , and the final FTIR spectrum s...

“: Fruit waste has increased exponentially worldwide, within which tangerine is one of those that generates a greater amount of organic waste, which is currently not fully used. On the other hand, microbial fuel cells (MFCs) are presented as an opportunity to take advantage of organic waste to generate electricity, which is why the main objective of this research is to generate bioelectricity using tangerine waste as a substrate in microbial fuel cells using zinc and copper electrodes. It was possible to generate current and voltage peaks of 1.43973 ± 0.05568 mA and 1.191 ± 0.035 V on days eighteen and seventeen, respectively, operating with an optimum pH of 4.78 ± 0.46 and with electrical conductivity of the substrate of 140.07 ± 3.51 mS/cm, while the Brix degrees gradually decreased until the last day. The internal resistance determined was 65.378 ± 1.967 Ω, while the maximum p...

“Fruit waste has increased exponentially worldwide, within which tangerine is one of those that generates a greater amount of organic waste, which is currently not fully used. On the other hand, microbial fuel cells (MFCs) are presented as an opportunity to take advantage of organic waste to generate electricity, which is why the main objective of this research is to generate bioelectricity using tangerine waste as a substrate in microbial fuel cells using zinc and copper electrodes. It was possible to generate current and voltage peaks of 1.43973 ± 0.05568 mA and 1.191 ± 0.035 V on days eighteen and seventeen, respectively, operating with an optimum pH of 4.78 ± 0.46 and with electrical conductivity of the substrate of 140.07 ± 3.51 mS/cm, while the Brix degrees gradually decreased until the last day. The internal resistance determined was 65.378 ± 1.967 Ω, while the maximum pow...

The accelerated increase in energy consumption by human activity has generated an increase in the search for new energies that do not pollute the environment, due to this, microbial fuel cells are shown as a promising technology. The objective of this research was to observe the influence on the generation of bioelectricity of sucrose, with different percentages (0%, 5%, 10% and 20%), in papaya waste using microbial fuel cells (MFCs). It was possible to generate voltage and current peaks of 0.955 V and 5.079 mA for the cell with 20% sucrose, which operated at an optimal pH of 4.98 on day fifteen. In the same way, the internal resistance values of all the cells were influenced by the increase in sucrose, showing that the cell without sucrose was 0.1952 ± 0.00214 KΩ and with 20% it was 0.044306 ± 0.0014 KΩ. The maximum power density was 583.09 mW/cm2 at a current density of 407.13 A/cm...

Fruit waste has increased exponentially worldwide, within which tangerine is one of those that generates a greater amount of organic waste, which is currently not fully used. On the other hand, microbial fuel cells (MFCs) are presented as an opportunity to take advantage of organic waste to generate electricity, which is why the main objective of this research is to generate bioelectricity using tangerine waste as a substrate in microbial fuel cells using zinc and copper electrodes. It was possible to generate current and voltage peaks of 1.43973 ± 0.05568 mA and 1.191 ± 0.035 V on days eighteen and seventeen, respectively, operating with an optimum pH of 4.78 ± 0.46 and with electrical conductivity of the substrate of 140.07 ± 3.51 mS/cm, while the Brix degrees gradually decreased until the last day. The internal resistance determined was 65.378 ± 1.967 Ω, while the maximum power...

Fruit waste has increased exponentially worldwide, within which tangerine is one of those that generates a greater amount of organic waste, which is currently not fully used. On the other hand, microbial fuel cells (MFCs) are presented as an opportunity to take advantage of organic waste to generate electricity, which is why the main objective of this research is to generate bioelectricity using tangerine waste as a substrate in microbial fuel cells using zinc and copper electrodes. It was possible to generate current and voltage peaks of 1.43973 ± 0.05568 mA and 1.191 ± 0.035 V on days eighteen and seventeen, respectively, operating with an optimum pH of 4.78 ± 0.46 and with electrical conductivity of the substrate of 140.07 ± 3.51 mS/cm, while the Brix degrees gradually decreased until the last day. The internal resistance determined was 65.378 ± 1.967 Ω, while the maximum power...

Fruit waste has increased exponentially worldwide, within which tangerine is one of those that generates a greater amount of organic waste, which is currently not fully used. On the other hand, microbial fuel cells (MFCs) are presented as an opportunity to take advantage of organic waste to generate electricity, which is why the main objective of this research is to generate bioelectricity using tangerine waste as a substrate in microbial fuel cells using zinc and copper electrodes. It was possible to generate current and voltage peaks of 1.43973 ± 0.05568 mA and 1.191 ± 0.035 V on days eighteen and seventeen, respectively, operating with an optimum pH of 4.78 ± 0.46 and with electrical conductivity of the substrate of 140.07 ± 3.51 mS/cm, while the Brix degrees gradually decreased until the last day. The internal resistance determined was 65.378 ± 1.967 Ω, while the maximum power ...

El objetivo del siguiente trabajo es estudiar la utilidad del pigmento obtenido de la cáscara de la batata morada para sensibilizar celdas solares. Las celdas se construyeron utilizando láminas conductoras de ITO recubiertas con una capa de nanopartículas de TiO2 como fotoánodo y carbono como contraelectrodo, se preparó un extracto alcohólico de cáscara de batata morada que se integró a la capa de TiO2 como colorante-sensibilizador. Se estudió el desempeño de las DSSC irradiándolas con luz a diferentes longitudes de onda con potencia constante. Los resultados electroquímicos muestran valores de VOC = 0.374 V, JSC = 0.0244 mA/cm2, FF = 0.471 y una eficiencia de 0.0143 % para cuando las celdas fueron irradiadas con luz de 470 nm. Los resultados de EIS confirman este desempeño al mostrar una baja resistencia al flujo de cargas libres bajo esta longitud de onda. Este trabajo con...

The environmental problems caused by the excessive use of fossil fuels for electricity generation have led to the development of new technologies. Microbial fuel cells constitute a technology that uses organic sources for electricity generation. This research gives a novel means of using Golden Berry waste as fuel for electricity generation through microbial fuel cells made at low cost, achieving current and voltage peaks of 4.945 ± 0.150 mA and 1.03 ± 0.02 V, respectively. Conductivity values increased up to 148 ± 1 mS/cm and pH increased up to 8.04 ± 0.12 on the last day. The internal resistance of cells was 194.04 ± 0.0471 Ω, while power density was 62.5 ± 2 mW/cm2 at a current density of 0.049 A/cm2. Transmittance peaks of the Fourier-transform infrared (FTIR) spectrum showed a decrease when comparing the initial and final spectra, while the bacterium Stenotrophomonas maltoph...

The environmental problems caused by the excessive use of fossil fuels for electricity generation have led to the development of new technologies. Microbial fuel cells constitute a technology that uses organic sources for electricity generation. This research gives a novel means of using Golden Berry waste as fuel for electricity generation through microbial fuel cells made at low cost, achieving current and voltage peaks of 4.945 ± 0.150 mA and 1.03 ± 0.02 V, respectively. Conductivity values increased up to 148 ± 1 mS/cm and pH increased up to 8.04 ± 0.12 on the last day. The internal resistance of cells was 194.04 ± 0.0471 Ω, while power density was 62.5 ± 2 mW/cm2 at a current density of 0.049 A/cm2. Transmittance peaks of the Fourier-transform infrared (FTIR) spectrum showed a decrease when comparing the initial and final spectra, while the bacterium Stenotrophomonas maltoph...

“A large amount of fruit waste is being a great environmental and social problem due to a lack of adequate storage. Among the most abundant waste is papaya, due to its high consumption in various varieties. These wastes can generate bioelectricity through organic waste, being an important parameter the pH. In this research, lowcost laboratory-scale microbial fuel cells were fabricated, using papaya waste as fuel at different pH (4, 5.73, 7, and 9) to obtain the optimum operating pH. It was possible to observe the maximum values of electric current and voltage of 17.97 mA and 1.02 V on days 16 and 14, in the cell with pH 7; while the cell with pH was the one that showed the lowest values. The electrical conductivity values increased from the first day, observing a maximum peak of 172.50 mS/cm for the cell with pH 7. However, the internal resistance values were low, the maximum value bei...

“The use of organic waste as fuel for energy generation will reduce the great environmental problems currently caused by the consumption of fossil sources, giving agribusiness companies a profitable way to use their waste. In this research, tomato waste with different percentages of sucrose (0-target, 5, 10, and 20%) was used in microbial fuel cells manufactured on a laboratory scale with zinc and copper electrodes, managing to generate maximum peaks of voltage and a current of 1.08 V and 6.67 mA in the cell with 20% sucrose, in which it was observed that the optimum operating pH was 5.29, while the MFC with 0% (target) sucrose generated 0.91 V and 3.12 A on day 13 with a similar pH, even though all the cells worked in an acidic pH. Likewise, the cell with 20% sucrose had the lowest internal resistance (0.148541 ± 0.012361 KΩ) and the highest power density (224.77 mW/cm2 ) at a curr...

Debido al aumento de la producción de frutos para consumo y exportación se está generando grandes cantidades de residuos de los mismos frutos, ocasionando un gran problema medio ambiental, sobre todo en los países en vías de desarrollo que no cuentan con un proceso adecuado para su utilización o tratamiento. En este contexto, se presentan las celdas de combustible microbiana como una tecnología novedosa que a futuro podrían dar solución a este problema mediante la reutilización de residuos orgánicos como fuente de energía. En el presente trabajo se fabricaron celdas de combustible microbiana (CCM) a escala de laboratorio utilizando como sustrato desechos de manzana con electrodos de Zinc y Cobre. Se logró generar picos de corriente eléctrica y voltaje de 7.567 ± .0117 mA y 1.452 ± 0.023 V, los cuales operaron con una conductividad eléctrica del sustrato de 152.326 ± 4.5...

The environmental problems caused by the excessive use of fossil fuels for electricity generation have led to the development of new technologies. Microbial fuel cells constitute a technology that uses organic sources for electricity generation. This research gives a novel means of using Golden Berry waste as fuel for electricity generation through microbial fuel cells made at low cost, achieving current and voltage peaks of 4.945 ± 0.150 mA and 1.03 ± 0.02 V, respectively. Conductivity values increased up to 148 ± 1 mS/cm and pH increased up to 8.04 ± 0.12 on the last day. The internal resistance of cells was 194.04 ± 0.0471 Ω, while power density was 62.5 ± 2 mW/cm2 at a current density of 0.049 A/cm2. Transmittance peaks of the Fourier-transform infrared (FTIR) spectrum showed a decrease when comparing the initial and final spectra, while the bacterium Stenotrophomonas maltoph...

A large amount of fruit waste is being a great environmental and social problem due to a lack of adequate storage. Among the most abundant waste is papaya, due to its high consumption in various varieties. These wastes can generate bioelectricity through organic waste, being an important parameter the pH. In this research, lowcost laboratory-scale microbial fuel cells were fabricated, using papaya waste as fuel at different pH (4, 5.73, 7, and 9) to obtain the optimum operating pH. It was possible to observe the maximum values of electric current and voltage of 17.97 mA and 1.02 V on days 16 and 14, in the cell with pH 7; while the cell with pH was the one that showed the lowest values. The electrical conductivity values increased from the first day, observing a maximum peak of 172.50 mS/cm for the cell with pH 7. However, the internal resistance values were low, the maximum value being ...