The enormous environmental problems that arise from organic waste have increased due to the significant population increase worldwide. Microbial fuel cells provide a novel solution for the use of waste as fuel for electricity generation. In this investigation, onion waste was used, and managedtogeneratemaximumpeaksof4.459±0.0608mAand0.991±0.02Vofcurrentandvoltage, respectively. The conductivity values increased rapidly to 179,987±2859 mS/cm, while the optimal pH in which the most significant current was generated was 6968 ± 0.286, and the ◦ Brix values decreased rapidly due to the degradation of organic matter. The microbial fuel cells showed a low internal resistance (154,389±5228 Ω), with a power density of 595.69±15.05 mW/cm2 at a current density of 6.02 A/cm2; these values are higher than those reported by other authors in the literature. The diffractogram spectra of the ...

This research used tomato waste as a substrate (fuel) in Single Chamber-Microbial Fuel Cells (scMFC) on a small scale. The electrochemical properties were monitored, the functional groups of the substrate were analyzed by Fourier Transform Infrared Spectrophotometry (FTIR) and a microbiological analysis was performed on the electrodes in order to identify the microorganisms responsible for the electrochemical process. The results show voltage peaks and an electrical current of 3.647 ± 0.157 mA and 0.957 ± 0.246 V. A pH of 5.32 ± 0.26 was measured in the substrate with an electrical current conductivity of 148,701 ± 5849 mS/cm and an internal resistance (Rint) of 77. 517 ± 8.541 Ω. The maximum power density (PD) displayed was 264.72 ± 3.54 mW/cm2 at a current density (CD) of 4.388 A/cm2. On the other hand, the FTIR spectrum showed a more intense decrease in its peaks, with the comp...

“: Fruit waste has increased exponentially worldwide, within which tangerine is one of those that generates a greater amount of organic waste, which is currently not fully used. On the other hand, microbial fuel cells (MFCs) are presented as an opportunity to take advantage of organic waste to generate electricity, which is why the main objective of this research is to generate bioelectricity using tangerine waste as a substrate in microbial fuel cells using zinc and copper electrodes. It was possible to generate current and voltage peaks of 1.43973 ± 0.05568 mA and 1.191 ± 0.035 V on days eighteen and seventeen, respectively, operating with an optimum pH of 4.78 ± 0.46 and with electrical conductivity of the substrate of 140.07 ± 3.51 mS/cm, while the Brix degrees gradually decreased until the last day. The internal resistance determined was 65.378 ± 1.967 Ω, while the maximum p...

Microbial fuel cells have undergone several modifications since their creation, mainly due to the different substrates that can be used as fuel for the generation of electrical energy. In this research, a deep and updated analysis of the characteristics of the literature published in the Scopus database from 1990 to 30 December 2022 has been carried out, finding 7055 documents indexed. The most used keywords are microbial fuel cells, performance, and electricity generation. From 2011 to the present, 5289 article-type documents were published; the article entitled “Microbial Fuel Cells: Methodology and Technology” by Logan B. E. et al., 2006 from Pennsylvania State University, USA in the Environmental Science and Technology journal of the ACS publisher was the most cited (4496 citations). On the other hand, in recent years, Chinese universities have begun to produce and highlight a nu...

This research aimed to use kiwi waste as fuel to generate bioelectricity through microbial fuel cells. It was possible to generate an electrical current and voltage peaks of 3.807 ± 0.102 mA and 0.993 ± 0.061 V on day 11, showing an electrical conductivity of 189.82 ± 3.029 mS/cm and an optimum operating pH of 5.966 ± 0.121. The internal resistance of the cells was calculated using Ohm’s Law, resulting in a value of 14.957 ± 0.394 Ω, while the maximum power density was 212.68 ± 26.84 mW/m2 at a current density of 4.506 A/cm2. Through the analysis of the FTIR spectra carried out on the substrate, a decrease in the characteristic organic peaks was observed due to their decomposition during the electricity-generation process. In addition, it was possible to molecularly identify the bacteria Comamonas testosteroni, Sphingobacterium sp., and Stenotropho-monas maltophila adhered to th...

“Abstract: Pollution generated by the misuse of large amounts of fruit and vegetable waste has become a major environmental and social problem for developing countries due to the absence of specialized collection centers for this type of waste. This research aims to generate electricity in an eco-friendly way using red dragon fruit (pitahaya) waste as the fuel in single-chamber microbial fuel cells on a laboratory scale using zinc and copper electrodes. It was possible to generate voltage and current peaks of 0.46 ± 0.03 V and 2.86 ± 0.07 mA, respectively, with an optimum operating pH of 4.22 ± 0.09 and an electrical conductivity of 175.86 ± 4.72 mS/cm at 8 ◦Brix until the tenth day of monitoring. An internal resistance of 75.58 ± 5.89 Ω was also calculated with a maximum power density of 304.33 ± 16.51 mW/cm2 at a current density of 5.06 A/cm2 , while the FTIR spectra showed ...

The environmental problems caused by the excessive use of fossil fuels for electricity generation have led to the development of new technologies. Microbial fuel cells constitute a technology that uses organic sources for electricity generation. This research gives a novel means of using Golden Berry waste as fuel for electricity generation through microbial fuel cells made at low cost, achieving current and voltage peaks of 4.945 ± 0.150 mA and 1.03 ± 0.02 V, respectively. Conductivity values increased up to 148 ± 1 mS/cm and pH increased up to 8.04 ± 0.12 on the last day. The internal resistance of cells was 194.04 ± 0.0471 Ω, while power density was 62.5 ± 2 mW/cm2 at a current density of 0.049 A/cm2. Transmittance peaks of the Fourier-transform infrared (FTIR) spectrum showed a decrease when comparing the initial and final spectra, while the bacterium Stenotrophomonas maltoph...

“The increase in the population and its need to produce food has caused the level of contamination by organic waste to increase exponentially in recent years. Innovative methods have been proposed for the use of this waste and thus to mitigate its impact. One of these is to use it as fuel in microbial fuel cells to generate electricity. This research aims to generate bioelectricity using coriander waste in microbial fuel cells. The maximum voltage and current observed were 0.882 ± 0.154 V and 2.287 ± 0.072 mA on the seventh and tenth day, respectively, these values were obtained working at an optimum operating pH of 3.9 ± 0.16 and with an electrical conductivity of 160.42 ± 4.54 mS/cm. The internal resistance observed in the cells was 75.581 ± 5.892 Ω, with a power density of 304.325 ± 16.51 mW/cm2 at 5.06 A/cm2 current density. While the intensity of the final FTIR (Fourier tra...

“The accelerated increase in energy consumption by human activity has generated an increase in the search for new energies that do not pollute the environment, due to this, microbial fuel cells are shown as a promising technology. The objective of this research was to observe the influence on the generation of bioelectricity of sucrose, with different percentages (0%, 5%, 10% and 20%), in papaya waste using microbial fuel cells (MFCs). It was possible to generate voltage and current peaks of 0.955 V and 5.079 mA for the cell with 20% sucrose, which operated at an optimal pH of 4.98 on day fifteen. In the same way, the internal resistance values of all the cells were influenced by the increase in sucrose, showing that the cell without sucrose was 0.1952 ± 0.00214 KΩ and with 20% it was 0.044306 ± 0.0014 KΩ. The maximum power density was 583.09 mW/cm2 at a current density of 407.13...

The environmental problems caused by the excessive use of fossil fuels for electricity generation have led to the development of new technologies. Microbial fuel cells constitute a technology that uses organic sources for electricity generation. This research gives a novel means of using Golden Berry waste as fuel for electricity generation through microbial fuel cells made at low cost, achieving current and voltage peaks of 4.945 ± 0.150 mA and 1.03 ± 0.02 V, respectively. Conductivity values increased up to 148 ± 1 mS/cm and pH increased up to 8.04 ± 0.12 on the last day. The internal resistance of cells was 194.04 ± 0.0471 Ω, while power density was 62.5 ± 2 mW/cm2 at a current density of 0.049 A/cm2. Transmittance peaks of the Fourier-transform infrared (FTIR) spectrum showed a decrease when comparing the initial and final spectra, while the bacterium Stenotrophomonas maltoph...

The excessive use of fossil sources for the generation of electrical energy and the increase in different organic wastes have caused great damage to the environment; these problems have promoted new ways of generating electricity in an eco-friendly manner using organic waste. In this sense, this research uses single-chamber microbial fuel cells with zinc and copper as electrodes and pineapple waste as fuel (substrate). Current and voltage peaks of 4.95667 ± 0.54775 mA and 0.99 ± 0.03 V were generated on days 16 and 20, respectively, with the substrate operating at an acid pH of 5.21 ± 0.18 and an electrical conductivity of 145.16 ± 9.86 mS/cm at two degrees Brix. Thus, it was also found that the internal resistance of the cells was 865.845 ± 4.726 Ω, and a maximum power density of 513.99 ± 6.54 mW/m2 was generated at a current density of 6.123 A/m2, and the final FTIR spectrum sho...

“Abstract: Pollution generated by the misuse of large amounts of fruit and vegetable waste has become a major environmental and social problem for developing countries due to the absence of specialized collection centers for this type of waste. This research aims to generate electricity in an eco-friendly way using red dragon fruit (pitahaya) waste as the fuel in single-chamber microbial fuel cells on a laboratory scale using zinc and copper electrodes. It was possible to generate voltage and current peaks of 0.46 ± 0.03 V and 2.86 ± 0.07 mA, respectively, with an optimum operating pH of 4.22 ± 0.09 and an electrical conductivity of 175.86 ± 4.72 mS/cm at 8 ◦Brix until the tenth day of monitoring. An internal resistance of 75.58 ± 5.89 Ω was also calculated with a maximum power density of 304.33 ± 16.51 mW/cm2 at a current density of 5.06 A/cm2 , while the FTIR spectra showed ...

Pollution generated by the misuse of large amounts of fruit and vegetable waste has become a major environmental and social problem for developing countries due to the absence of specialized collection centers for this type of waste. This research aims to generate electricity in an eco-friendly way using red dragon fruit (pitahaya) waste as the fuel in single-chamber microbial fuel cells on a laboratory scale using zinc and copper electrodes. It was possible to generate voltage and current peaks of 0.46 ± 0.03 V and 2.86 ± 0.07 mA, respectively, with an optimum operating pH of 4.22 ± 0.09 and an electrical conductivity of 175.86 ± 4.72 mS/cm at 8 °Brix until the tenth day of monitoring. An internal resistance of 75.58 ± 5.89 Ω was also calculated with a maximum power density of 304.33 ± 16.51 mW/cm2 at a current density of 5.06 A/cm2, while the FTIR spectra showed a decrease in t...

“The accelerated increase in energy consumption by human activity has generated an increase in the search for new energies that do not pollute the environment, due to this, microbial fuel cells are shown as a promising technology. The objective of this research was to observe the influence on the generation of bioelectricity of sucrose, with different percentages (0%, 5%, 10% and 20%), in papaya waste using microbial fuel cells (MFCs). It was possible to generate voltage and current peaks of 0.955 V and 5.079 mA for the cell with 20% sucrose, which operated at an optimal pH of 4.98 on day fifteen. In the same way, the internal resistance values of all the cells were influenced by the increase in sucrose, showing that the cell without sucrose was 0.1952 ± 0.00214 KΩ and with 20% it was 0.044306 ± 0.0014 KΩ. The maximum power density was 583.09 mW/cm2 at a current density of 407.13...

The excessive use of fossil sources for the generation of electrical energy and the increase in different organic wastes have caused great damage to the environment; these problems have promoted new ways of generating electricity in an eco-friendly manner using organic waste. In this sense, this research uses single-chamber microbial fuel cells with zinc and copper as electrodes and pineapple waste as fuel (substrate). Current and voltage peaks of 4.95667 ± 0.54775 mA and 0.99 ± 0.03 V were generated on days 16 and 20, respectively, with the substrate operating at an acid pH of 5.21 ± 0.18 and an electrical conductivity of 145.16 ± 9.86 mS/cm at two degrees Brix. Thus, it was also found that the internal resistance of the cells was 865.845 ± 4.726 Ω, and a maximum power density of 513.99 ± 6.54 mW/m2 was generated at a current density of 6.123 A/m2, and the final FTIR spectrum sho...

“This research used tomato waste as a substrate (fuel) in Single Chamber-Microbial Fuel Cells (scMFC) on a small scale. The electrochemical properties were monitored, the functional groups of the substrate were analyzed by Fourier Transform Infrared Spectrophotometry (FTIR) and a microbiological analysis was performed on the electrodes in order to identify the microorganisms responsible for the electrochemical process. The results show voltage peaks and an electrical current of 3.647 ± 0.157 mA and 0.957 ± 0.246 V. A pH of 5.32 ± 0.26 was measured in the substrate with an electrical current conductivity of 148,701 ± 5849 mS/cm and an internal resistance (Rint) of 77. 517 ± 8.541 Ω. The maximum power density (PD) displayed was 264.72 ± 3.54 mW/cm2 at a current density (CD) of 4.388 A/cm2 . On the other hand, the FTIR spectrum showed a more intense decrease in its peaks, with the ...

“A large amount of fruit waste is being a great environmental and social problem due to a lack of adequate storage. Among the most abundant waste is papaya, due to its high consumption in various varieties. These wastes can generate bioelectricity through organic waste, being an important parameter the pH. In this research, lowcost laboratory-scale microbial fuel cells were fabricated, using papaya waste as fuel at different pH (4, 5.73, 7, and 9) to obtain the optimum operating pH. It was possible to observe the maximum values of electric current and voltage of 17.97 mA and 1.02 V on days 16 and 14, in the cell with pH 7; while the cell with pH was the one that showed the lowest values. The electrical conductivity values increased from the first day, observing a maximum peak of 172.50 mS/cm for the cell with pH 7. However, the internal resistance values were low, the maximum value bei...

“The use of organic waste as fuel for energy generation will reduce the great environmental problems currently caused by the consumption of fossil sources, giving agribusiness companies a profitable way to use their waste. In this research, tomato waste with different percentages of sucrose (0-target, 5, 10, and 20%) was used in microbial fuel cells manufactured on a laboratory scale with zinc and copper electrodes, managing to generate maximum peaks of voltage and a current of 1.08 V and 6.67 mA in the cell with 20% sucrose, in which it was observed that the optimum operating pH was 5.29, while the MFC with 0% (target) sucrose generated 0.91 V and 3.12 A on day 13 with a similar pH, even though all the cells worked in an acidic pH. Likewise, the cell with 20% sucrose had the lowest internal resistance (0.148541 ± 0.012361 KΩ) and the highest power density (224.77 mW/cm2 ) at a curr...

This research aimed to use kiwi waste as fuel to generate bioelectricity through microbial fuel cells. It was possible to generate an electrical current and voltage peaks of 3.807 ± 0.102 mA and 0.993 ± 0.061 V on day 11, showing an electrical conductivity of 189.82 ± 3.029 mS/cm and an optimum operating pH of 5.966 ± 0.121. The internal resistance of the cells was calculated using Ohm’s Law, resulting in a value of 14.957 ± 0.394 Ω, while the maximum power density was 212.68 ± 26.84 mW/m2 at a current density of 4.506 A/cm2. Through the analysis of the FTIR spectra carried out on the substrate, a decrease in the characteristic organic peaks was observed due to their decomposition during the electricity-generation process. In addition, it was possible to molecularly identify the bacteria Comamonas testosteroni, Sphingobacterium sp., and Stenotropho-monas maltophila adhered to th...

Microbial fuel cells are a bioelectrochemical technology that uses different types of waste as fuel sources to generate sustainable and environmentally friendly electricity. Various MFCs have been developed, with the electrode used being a crucial problem due to its high manufacturing cost. This research shows that electrodes can be manufactured quickly and economically using activated carbon (100 g), sugar (80 g), ethanol (250 ml), and pine resin (200 g). For its demonstration, grape waste was used in a single-chamber MFC for 35 days. The manufactured electrode generated a Rint. of 18.471 ± 2.475 Ω, whose current density was 8.348 ±0.768 mW/cm2 at a current density of 5.166 A/cm2. The electrical potential shown was 0.889 ± 0.017 V and 4.571 ± 0.061 mA, with an ORPmax of 81.495 ± 1.874 mV, operating at a pH of 7.26 ±0.19. The micrographs made by scanning electron microscopy showed...